Automatic Gate Access Device

1. Introduction For the standard one entry/exit system, it includes two sets of Long Range RFID Readers, two sets of Automatic Barrier Gates, two sets of Parking Controllers, two sets of Loop Detectors and one set of PC. It can also be used in multiple entry/exit system and the principle is the same. 1) Entry Station It mainly includes Long Range RFID Reader, Loop Detector, Entry Parking Controller, Automatic Barrier Gate and Loop coils. The drivers stick the Long Range RFID Transponder on the car windshield. When the car enters the RFID Long Range Reader reading area, the RFID Readers will activate RFID Transponder and read its information. The Entry Parking Controller will determine its effectiveness. If it is effective, the Automatic Barrier Gate will open. After the Loop Detectors detects that the car has passed, the barrier gate will close. If the RFID Transponder is invalid, the barrier gate will not open. 2) Exit Station It mainly includes Long Range RFID Reader, Loop Detec...

Safety Wired Photocell Infrared Sensor For Automatic Doors And Gate Openers Safety Wired Photocell Infrared Sensor For Automatic Doors And Gate Openers D escription: Safety wired photocell infrared sensor for automatic doors and gate openers with range up to 20m Product Features Power supply 12-24 Vca-Vdc Range up to 20 mt in all environments Protection against interference Anti-blinding circuit for protection from sunlight Protection against environmental factors IP 55 Basic Parameter  of  IR-20M Safety Wired Photocell Infrared Sensor For Automatic Doors And Gate Openers : Product Name: Active Infrared Detector  Power Supply:12/24VAC/DC Detecting Distance:with 20m stable detection distance Max.Range Up:20Meters(Indoor or Outdoor) Operate Temperature:-10degree-60 degree Max.TX working Current:25mA Max.RX working Current:35mA Max.Relay Contract:Max 500mA e 48Vac/dc IP rate:IP65 Cover Material:Anti-UV Material Can working at outside directly...

20m Outdoor IP55 Beam Infrared Detector/Photo IR Beam Sensor with door used/Alarm system Install each pair at the opposite positions.Then there is a infrared area between these two detector parts. When someone passes the infrared region, the detector will send alarm signal to the security alarm host (which not included here). Install Distance(Max.)in the above chart means the maximum install distance between the twodetector parts. Great to be installed for security system in school, office building, hosipital, home yard, etc. Detecting range can be reduced to 30% in bad weather conditions, like rain, dust, etc. English Usage Manual included in the pack. It will give you detailed instructions Single Beam Infrared Sensor   Sealed design to anti-rain (fog), dust (worms) and other integrated weather, the detector sensitivity will increase automatically(AGC circuit)    With high levels of anti-RFI / EMI capability  High-power transmitter, sensitivity sur...

Vehicle Loop Detector Installation Guide   Feature It has excellent corrosion resistance oil resistance,strong acid,strong alkali resistant to high voltage. Small loss at high frequency, no moisture absorption, insulation resistance; It has excellent flame resistance, aging resistance, long service life. Anti-corrosion, anti-combustion, perfect insulation,  Acid-Alkaline resistant JUTAI Loop Wire Specification Model: JTHT-11 Size: 0.5m*2 Temperature: -65℃ to +200℃ One Roll Length: 305m Material: Silicone rubber and standed silver plated copper wire Color: Red and Black     1. The detector should be installed in a waterproof housing as close to the loop as possible. 2. The loop and feeder should be made from insulated copper wire with a minimum cross-sectional area of 1.5mm2. The feeder should be twisted with at least 20 turns per metre. Joints in the wire are not recommended and must be soldered and made waterproof. Faulty joi...

Vehicle Loop Detector Dual LD-202 Channel 12-24v ADC Includes: 1 x Dual Detector with wiring connector block (fitted under detector unit) only. Inductive Loop Cable: we also can provide loop cable 1roll 305m. Double channel vehicle loop detectors are used to identify the presence of vehicles by means of two independent inductive loops buried under the road and can be used in almost any application. Dual channel vehicle loop detectors can be used as an alternative to two single channel detectors to eliminate any presence of crosstalk. They also feature A-B logic to detect the direction of vehicles crossing the loops. All detectors are CE tested and approved.

1.JUTAI loop detector with high sensivity level, 20-2000uH Inductive value,easy to make underground loop coil,can detect nearly all types vehicles,like motocyle,car,truck,etc. 2.Fast respond time, can detect fast speed vehicle, car parking system/traffic control/bollard/autogate,use for many applications. 3.Fault output function and that can be self-adjustable,very high quality for your projects. 4. working voltage: 100-240v, 12-24VADC. Any inqury please contact with us:sales9@jutairfid.com Whatsapp"008615992504234 #loopdetector #loopsensor #parkingloop #trafficloop #autogate #caraccesscontrol #vehicledetector #LD100 #LD200 #LD102 #LD202